Variable Inductance Linear Position Sensors for Use in Hydraulic Cylinders
Moorestown, NJ USA, July 2, 2015 (Newswire.com) - Variable inductance position sensors, known as LVITs (Linear Variable Inductance Transducers), have been around for several decades. Recent advancements in electronics and flexibility of package designs have made LVIT variable inductance sensors cost effective for mainstream in-cylinder applications. This contactless technology offers many significant advantages regarding product life and long-term reliability over some competitive technologies, and competes very favorably in performance with all competitors for specifications such as non-linearity, resolution, and frequency response, but at a significantly lower cost. Equally important is the fact that LVIT sensors can typically withstand greater shocks and vibration, such as those commonly found in heavy industrial and mobile equipment applications for cylinders.
Linear variable inductance sensors operate by measuring the resonant frequency of an oscillator that uses a simple inductive probe. Its inductance is varied by the position of a conductive tube or gun-drilled rod that surrounds it, as seen in Figure 1. LVITs are typically offered in full-scale ranges from 4 inches (100 mm) to 36 inches (900 mm). Both port-mounted and internally embedded packages are available, with either connector or cable terminations. Figure 2 shows examples of both packages. These sensors produce an analog DC voltage or current output, with a digital output available for OEM applications.
Remote field calibration is a standard feature offered on LVIT variable inductance sensors. This feature permits a user to scale the analog output of the sensor after it has been installed in the cylinder. By merely grounding a wire to set the zero and full-scale output points, the sensor will give the desired full-scale output over its newly set range, making it unnecessary to scale the unit in an actual control system.
LVIT variable inductance sensors in cylinders offer a contactless position sensing solution that does not require machining a cavity in the cylinder piston for a ring magnet or wiper contact. In fact, if an LVIT sensor were installed to replace an existing magnetostrictive sensor, the magnet could be left in place in the cylinder rod end without interfering with the inductive sensor’s basic operation.
In the past few years, requirements for instrumented cylinders in subsea applications have dramatically increased. Variable inductance sensors can be offered in a pressure-sealed version that allows a user to install the sensor and cylinder in a subsea environment in depths of 12,000 feet (3,650 m) with 3,000 psig of internal hydraulic pressure.
Another application for LVITs similar to cylinder position sensing is spool position feedback for two-stage hydraulic valves. A short range (<1 inch) port-mounted LVIT sensor having its probe inserted into a blind hole in one end of the main spool is almost always an easier and lower cost installation than a pressure-sealed LVDT which requires an isolation tube to seal off its windings from the valve’s pilot pressure and which also needs relatively expensive electronics to operate it.
In summary, an LVIT position sensor has many advantages when used in a cylinder. Whether inserted into an O-ring port or embedded in the cylinder endcap, an LVIT features simplicity, needing just a deep hole in the piston rod. It offers excellent operating characteristics such as linearity, repeatability, stability, and temperature coefficient at much lower cost than other sensors having the same general mechanical configuration. In addition, an LVIT is remarkably rugged and resistant to shock and vibration-induced failure. Furthermore, an LVIT has a very long service life because it works without any physical contact between the sensor probe and the bore of the deep hole, or without using an electrical contact that can wear out. Altogether, these features make an LVIT the optimum choice for a broad range of fluid power position sensing applications, particularly for in-cylinder position sensing.
About H. G. Schaevitz LLC Alliance Sensors Group
Headquartered in Moorestown, NJ USA, Alliance Sensors Group a div of H.G. Schaevitz LLC (www.alliancesensors.com) is a position sensor manufacturing company offering engineering and application support toward solving position measurement challenges within the power generation, fluid power, and manufacturing industries. Combining more than 150 years of sensors know-how, ASG's technical and applications support staff have extensive experience in providing the right sensor for difficult rotary and linear position measurement applications. Follow us on Twitter (@Alliancesensor1) or Facebook.
